Exactly how to Install a Tub (Step By Step).
Exactly how to Install a Tub (Step By Step).
Blog Article
Just how do you actually feel on the subject of Tools You Need to Install a New Bathtub ?
Setting up a bath tub isn't specifically rocket science, however it does require solid plumbing, woodworking, and also sometimes, tiling skills. Replacing an old tub with a brand-new one is also a moderately tough job. If the old bathtub is conveniently available, the project can move quickly; if you have to open a wall surface to eliminate the old bathtub and also position the new tub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly require an assistant to move out the old tub and set in the brand-new one. See to it you have actually certified on your own for the job and are comfortable trying it. Instead of working with a contractor to take over a halfway-completed job, it is much better to think about using one prior to you start. Opportunities are you might require a specialist plumber to make tube links.
This write-up will certainly aid you install a brand-new bath tub in your washroom if you have actually currently acquired a brand-new bathtub and also do not require to transform the plan of your previous supply of water pipes.
Your tools and material checklist should consist of the following:
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you ought to do is detach the supply of water. After doing so, turn on the taps to drain any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite problematic as a result of the limited access that is often the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a cloth all set for the staying water that will originate from the pipelines. When the supply pipes have actually been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from transforming during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Prior to proceeding to fit the new faucets, compare the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end gives a connection to the current supply pipes.
If you need to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, place the tap in the installing hole in the bath/basin making sure that the washers remain in place in between the tap as well as the sink. Secure the tap in position with the manufacturer given backnut. When the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal faucet connectors. The previous type needs to be linked to the faucet ends initially, tightening just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Bathtub
Making use of the two wood boards under its feet, place the tub in the required setting. The wooden boards are valuable in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 small factors.
The following goal is to make certain that the bathtub is leveled all round. This can be accomplished by checking the spirit level and also adjusting the feet on the tub until the spirit level reviews level.
To set up faucets, fit the bottom of the outermost adaptable tap port to the appropriate supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Switch on the water system and also check all joints as well as brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as also check the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, take care of the bathroom paneling as described in the supplier's instruction manual. Tiling as well as securing around the bath tub should wait up until the tub has actually been used at least once as this will resolve it right into its final setting.
Getting ready for the Setup
Firstly, the sustaining frame supplied with the bath must be fitted (if called for) according to the manufacturer's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is important to make sure that if the tap includes a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the flexible tap ports to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom must now be ready to be fitted in its last placement.
Tiling Around the Tub
In the area where the bath meets the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to crack a rigid seal, creating the water to permeate the wall in between the bathroom as well as the tiling, resulting in complications with wetness as well as possible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and also installations. They are offered in tubes and cartridges, and also are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of soaked paper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to allow for the activity experienced when the tub remains in usage. The sealant can fracture relatively very early if you do not think about this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily offered on the market. It is advisable to fit the ceramic tiles using waterproof or waterproof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
We were made aware of that write-up about Installing A Bathtub from an associate on a different blog. Sharing is caring. Who knows, you may very well be doing someone a favor. Bless you for your time. Visit us again soon.
Visit Our Site Report this page